Fused Staples Dual (SERIES)
Fused Staples Dual
.4mm ni80*38ni80 3mm ID
These coils are best suited for regulated mod's or those in series configuration
This coil contains only ni80 ribbon wire with no round wire frames, bringing you the best performance possible for your vaping experience, this type of coil is well suited all round for cloud production and flavour, a very flavoursome vape, handcrafted to perfection each and every time.
(FIRST TIME FIRING SHOULD BE DONE ON LOW WATTS TO AVOID DAMAGE TO THE COILS)
You will have to agree to our terms on coil misuse at the checkout before purchasing this product.
All wicked wires uk coils are sterilised prior to packing and go
through a triple stage quality check process before being packaged for
postage to our customers.
How to install
Some coils may ohm lower than your device can fire (staggertons .08-.10Ω
, framed staples .12Ω
in this instance it is advised to fit one coil at a time, if using a
regulated device use a low wattage, 15-25 watts depending on the ohm of
the coil,trim the legs of both coils to the desired length required by
your device, fit each coil to its dedicated posts ensuring you are using
the correct posts for your device.
coil legs are cut to length evenly, correctly and any trailing wires
have been removed. Check that none of the coils are touching any of the
externals of the rda they are fitted too or the 510 pins for single coil
It is advised to now remove the
grease and oils that have been applied to the coil from your hands
during fitting, by either using an ultra sonic cleaner or some hot soapy
water and a clean small soft nylon brush to clean the coils (remove
from vape device when doing this) give the coils a good rinse in hot
water and refit to your vape device at a low wattage.
that post screws are not tighten too tight as this can damage the legs
on more fragile coils such as fused staples and cause the legs to snap
at the post holes, this can also cause the coil to read incorrect ohms
when in use (some fluctuation of final ohms readings are a good
indication of damage caused by incorrect fitting in this manner, usually
seen at the re-wick stage of coil care and a good indication of coil
Once happy with the fit of
the coils check there are at the same height as the air flow holes on
your rda cap, by inserting the coiling tool and gently lifting or lower
the coil into place, again making sue that both coils are not touching
any parts of the rda accept where they are secured into the post holes.
power to the coils and bring to a gentle amber glow, hot spots may
appear in the form of bright white/red spots, to remove these,
discontinue applying power to the coils and strum the coils using your
ceramic tweezers, or pull the individual coils of the coil apart (hot
spots are generally caused by the individual coils of the coil touching
and causing a short)
how to maintain wicked wires uk coils.
you find you have one coil heating quicker then another, check both
coils are set at the same distance from the posts that they are
connected to, check the ID (inner diameter) of each coil has not been
changed due to the fitting process, by using the correct size coiling
tool and gently tugging on each coil to correct that coils ID.
(ensure the coils are secured in place correctly before doing this,
wicked wires uk is not responsible for any damage caused to coils during
the fitting process, we advise only experienced vapers use our coils
due to this)
How to maintain wicked wires uk coils
some use the coils may begin to look a little black or dark, this can
easily be cleaned off by using some of the following steps.
your rda off of your device and put onto an ohm reader or a regulated
device with fully charged batteries (DO NOT PERFORM THIS STAGE ON A
dry burn your coils by removing your wick, apply low power to your coils
at around 20-30 watts to produce a low amber glow, as this occurs any
sugars that have built up on the coils should burn away, once this
begins release the power on your device and set to one side to allow the
device and the coils to cool naturally.
(DO NOT RUN UNDER WATER)
the device and coils have cooled, remove your rda/rdta from your
device, take to a sink and wash the coils and rda with a soft nylon
brush (toothbrush works well) and some warm soapy water, with more
complex coils be gentle if using this process to clean coils. give the
coils and rda a good rinse with clean warm/hot water and shake off
excess water before fitting back to your device.
wires uk recommend you use an ultra sonic cleaner for long term
solution for this process with 2 or 3 cycles run if possible)
should now perform the same steps as you did when you fitted the coils
from new, to ensure all the screws in the posts are still tight after
being cleaned, that the coils themselves have not degraded to a state
that they require replacing, check the integrity of the insulators on
your rda before applying power to it again, check that the 510 pin on
the rda/rdta is correctly tightened and then re-glow both coils to
ensure they are glowing evenly (if in doubt follow the first steps in
these how to tips)
Once happy with the cleanness and fit of the coils allow to cool, re-wick and vape!
wires uk is not responsible to damaged caused to coils/rda/rdta/mods or
any individual due to incorrect fitting, or caused due to general
maintenance or use of wicked wires uk hand made coils, the information
and tips described above are to be used at the customers own risk and as
a general how to guide, you should be sure you have sufficient
knowledge of ohms law, correct battery safety and general use. That you
have a good understanding of how to use rebuild-able vape devices and
when purchasing wicked wires uk coils you do so at your own risk)